If you write code for Arduino or ESP32, you have probably spent an evening debugging a sketch that was fine all along. The real bug was a dead LED, a reversed diode or a dried-out capacitor.
A cheap digital multimeter catches all of these in about two minutes. Here are the four checks I teach every beginner: resistor, diode, LED and capacitor. For each one: which mode, where the probes go, and what a good and a bad reading look like.
Before you start
- Test parts out of the circuit, with no power. A part still soldered to a board reads wrong because other parts sit in parallel with it.
- Discharge capacitors first. Big ones from power supplies, TVs or inverters can hold a dangerous charge. Practise on small capacitors rated 50 V or less.
- Black probe in COM, red probe in VΩ. Never use the 10A / mA jack for these tests.
Cheat sheet: where the probes go
| Test | Meter mode | Red probe | Black probe |
|---|---|---|---|
| Resistor | Ω | Either leg | Other leg |
| Diode, forward | Diode | Anode (no stripe) | Cathode (stripe) |
| Diode, reverse | Diode | Cathode | Anode |
| Electrolytic capacitor | Capacitance (F) | + (long leg) | − (stripe side) |
| Ceramic capacitor | Capacitance (F) | Either leg | Other leg |
| LED | Diode | Long leg (anode) | Short leg / flat side |
1. Resistor
Read the colour bands first (brown-black-red-gold = 1 kΩ ±5%), set the dial to Ω (on a manual meter, the range just above the expected value) and touch one probe to each leg. Don't hold both legs with your fingers: your body's resistance lowers the reading.
- Good: inside tolerance. A 1 kΩ ±5% resistor reads 950–1050 Ω.
- Bad:
OLon every range = open inside. A value far from the colour code, or a dark, cracked body = burnt.
Tip: touch the probes together first. The 0.1–0.5 Ω you see is lead resistance.
2. Diode
Diode mode pushes a small current and shows the voltage drop.
- Good: forward (red on anode) reads about 0.5–0.7 V for a silicon diode like 1N4007/1N4148 (Schottky like 1N5819: ~0.15–0.45 V). Reverse reads
OL. - Bad:
OLboth ways = open. Near0.000both ways (often with a beep) = shorted.
3. LED
An LED is a diode, so it's diode mode again: red on the long leg, black on the short leg.
- Good: a red LED reads about 1.6–2.0 V and often glows faintly. Reversed:
OL. - Watch out: blue, white and some green LEDs need 2.6–3.2 V. Many cheap meters can't supply that, so a good LED shows
OL. Test those on 5 V through a 220 Ω resistor (an Arduino's 5V and GND pins work). If it lights, it's fine.
4. Capacitor
- Discharge it: hold a 1 kΩ resistor across the legs for a few seconds. Never short a big capacitor with a screwdriver.
- Set the dial to capacitance (F or -|(-), red on +, black on −, and wait a few seconds.
- Good: near the printed value. Electrolytics are usually ±20%, so a 100 µF cap reading 82–120 µF is fine. A ceramic marked 104 = 100 nF.
- Bad: far below the printed value = dried out. ~0 Ω in resistance mode = shorted. A bulging or leaking top = replace it, whatever the meter says.
No capacitance mode? On a cap of 10 µF or more, use the 20k–200k Ω range. A good cap shows a value that climbs to OL as the meter charges it. Stuck at a fixed low value = shorted.
When the readings look weird
| Problem | Likely cause |
|---|---|
| Reading jumps around | Loose contact or oxidised legs: press firmly, scrape the legs |
| Resistor reads low | Fingers on both legs, or the part is still in the circuit |
OL on everything | Range too low, or red probe in the wrong jack |
| Capacitor value keeps climbing | Big capacitor, meter still charging: wait 10–20 s |
| Everything unstable | Low meter battery |
| Diode mode beeps on a good diode | Trust the number, not the beep |
The full guide (parts list, FAQ, and the next project to build with your tested parts) is on ElectroDai: How to Test a Resistor, Diode, Capacitor and LED with a Multimeter.
I write beginner Arduino, ESP32 and robotics tutorials for students in Nepal. All the example code is open source at github.com/electrodai/electrodai-projects.