The first stencil most people cut from a photo fails in the same place. The outline looks fine on screen, the knife work goes well, and then the centre of a letter O or the pupil of an eye drops onto the table. The sheet now has one big hole where two shapes used to be, and the painted result is a blob.

That loose piece is called an island. Dealing with islands is most of what separates a stencil that works from a nice-looking black and white picture.

A stencil is a sheet with holes

Paint goes through the holes and lands on the wall, board or fabric underneath. Everything that is not a hole has to stay in one connected piece, because it is a single sheet of card or plastic and nothing else is holding it up.

A photo converted to two tones does not follow that rule. A ring becomes a black circle with a white disc inside it. Cut along the black, and the white disc has no connection to the rest of the sheet. The same thing happens with the letters A, B, D, O, P, Q and R, with eyes, with buttons, and with any highlight that sits inside a dark area.

Bridges

A bridge is a thin strip of sheet left in place between an island and the frame around it. Street artists and sign painters have used them for a long time. Stencil typefaces, the ones you see on shipping crates, are regular letters with bridges already drawn in.

You can add bridges by hand. Print the two-tone image, look for every white shape that is fully surrounded by black, and draw a narrow white strip across the black to connect it to the nearest outside area. On a simple logo this takes a minute. On a portrait there can be dozens of islands, and it is easy to miss one until the knife frees it.

This is the part worth handing to software. The spray paint stencil maker on StencilBench converts a photo into a one-layer cut stencil in the browser, finds each island and joins it to the main sheet along the shortest path. The bridge width is a slider, and the photo is not uploaded anywhere. PNG, SVG and PDF downloads are free.

How wide should a bridge be

A bridge leaves a thin unpainted gap in the finished image, so there is a trade-off.

  • Narrow bridges are less visible in the painted result, but they tear more easily. They suit tough sheet such as acetate or mylar.
  • Wide bridges are sturdier and forgiving when the knife slips. They suit card and stiff paper, which weaken once they have soaked up paint.

Start with the default width. If the sheet feels flimsy when you lift it, make a new version with wider bridges and cut again. A stencil that survives several uses is worth a slightly more visible gap.

Pick a photo that will survive being cut

Bridges cannot rescue a bad source image. Three things help before you touch any setting.

  • Contrast. A face lit from one side separates into clear shapes. Flat, even light gives grey mush that turns into noise.
  • A plain background. A busy background becomes hundreds of small holes. Crop tightly, or choose a subject against a wall or the sky.
  • Fewer tiny pieces. Small specks are hard to cut and let paint creep underneath. Remove them in the tool before you print. Tiny white holes are a problem too, because a sliver of paper that small will not hold together.

If the preview is a solid black mass, lower the detail setting. If shapes you need are missing, raise it.

Choose a material

Card and stiff paper are easy to cut with a craft knife and fine for a handful of uses. Acetate and mylar last longer and wipe clean. If you own a cutting machine, load the SVG and let it follow the shapes, then check the bridges in the preview of your cutting software before you start the job.

Paint without bleeding

Most ruined prints come from paint getting under the edge of the sheet.

  • Tape the stencil flat, and press it down near the bridges, since those are the parts most likely to lift.
  • Hold the can square to the surface. Spraying at an angle pushes paint under the edges.
  • Use several light passes. One heavy pass pools and runs.
  • Lift the sheet straight up when you are done. Dragging it smears wet paint.

Always test on scrap first. A test shows whether the bridges hold, whether small details read at the size you printed, and whether the photo needed a different detail level.

More than one colour

A single sheet gives a single colour. For two or three colours, make a separate stencil for each tone: a low detail setting produces the darkest shapes, and a higher one adds the mid tones. Paint the lightest colour first, let it dry, then line up the next sheet over it. Registration marks in the corners of each sheet make the alignment much easier.

Only use images you have the right to use

A converter does not know who owns a photo. If the picture is not yours, get permission before you turn it into a stencil and paint it somewhere public.

Once the islands are handled, cutting a stencil from a photo is mostly patience: a sharp blade, a flat surface, and a test spray before the real one.